Every linear guide has to carry a load along a path with as little play as possible. How tightly the guide is fit, known as preload, decides how stiff it feels, how smoothly it moves, and how long it lasts. This guide explains preload using Helix miniature linear guides, then walks through the other Helix guide families so you can see which one fits your application.

Miniature Linear Guides
HMR miniature linear guides are made from stainless steel and use two rows of recirculating balls in a Gothic profile with a 45 degree contact angle, which gives equal load capacity in all directions. They come in sizes 2 through 15, in standard and wide versions, with three accuracy grades: Precision (P), High (H), and Normal (N). Speeds reach 3 m/s on SS and ZZ blocks and 5 m/s on EE and EZ blocks, and the largest wide block has a dynamic load rating of 6,725 N.
What preload is
Preload is a controlled load between the runner block and the rail that removes internal play. According to the catalog, preload improves stiffness, precision, and torsion resistance, but it reduces life and increases friction. The right class balances those effects for your application.
The three preload classes
- Clearance (V0): 4 to 0 microns of clearance at size 9. Catalog use: very smooth.
- Standard (VS): 2 to 0 microns of clearance at size 9. Catalog use: smooth and precise.
- Light preload (V1): 0 to -4 microns at size 9. Catalog use: high rigidity, minimized vibration, high precision, and load balance.
Clearance and Standard leave a very small gap. Light preload is the only class with negative clearance. The figures above are for size 9. Check out our Miniature Linear Guides catalog which lists the values for every size.
How to choose
- If smooth, low-friction travel matters most, choose Clearance (V0).
- If you want smooth and precise travel, choose Standard (VS).
- If rigidity, vibration control, precision, or load balance matter most, choose Light preload (V1).
Mounting matters
Mount the guide on a surface that is ground or fine milled to a roughness of Ra 1.6. An inaccurate mounting surface can reduce operating accuracy and shortens rated life.
Preload is part of the model code, so you specify it when you order: V0 for Clearance, VS for Standard, or V1 for Light preload.
Ratings and lubrication
Dynamic load ratings (C100) are based on 100 km of travel under ISO 14728-1, and the equivalent load on the runner block should not exceed half of the dynamic rating. For lubrication, the interval should not exceed one year, with lubricant added before it is contaminated or changes color. We recommend our Lead Screw Grease, and a Medical Grade Grease option is available for clean room environments.

Miniature Precision Torque Splines
Helix Miniature Precision Torque Splines transmit torque with low friction while allowing linear travel. The standard PTS bushing has rotational backlash of 0.005 to 0.009 inch. The PTA anti-backlash bushing is preloaded to eliminate radial movement, giving zero backlash, better repeatability, and more stiffness.
Shaft diameters are 1/4, 3/8, and 1/2 inch with 4, 6, and 8 teeth. The inner race is 304 stainless steel with an H4X PTFE coating. Splines are straight within 0.003 inch per foot and operate from -65°F to 200°F with proper lubrication.

300 Series Linear Slides
The 300 Series is a linear slide with guide rods, available with NEMA 11, 17, or 23 motors in single or double stack lengths. Travel runs up to 10 inches on NEMA 11, 18 inches on NEMA 17, and 24 inches on NEMA 23.
Choose a ball nut, a freewheeling nut, or an anti-backlash nut, with leads from 0.025 to 1.0 inch. Options include encoders from 200 to 2000 counts per revolution, optical end sensors, and smart motors with pluggable or M12 connectors.

200 Series Linear Stages
The 200 Series arrives as a complete assembled system: linear bearing pillow blocks, integrated end supports, HG linear shafts, a carriage plate, and an acme screw assembly. Choose end-supported (212) or fully supported (252) mounting, shaft diameters from 0.5 to 1.5 inches, lengths from 18 to 72 inches, and NEMA 23, 34, 42, or 56 motor adapters.
Options include bellows boots, a range of screw leads, specialized motor mounts, and custom carriage plate machining.

Telescoping Linear Guide Rails
Helix telescoping rails are designed for heavy loads and come in partial extension (HTPE) and full extension (HTDB) styles in sizes 28 and 43. Partial extension rails travel part of their length, for example 1,013 mm of stroke on a 1,970 mm HTPE43. Full extension rails travel beyond their length, for example 2,026 mm of stroke on a 1,970 mm HTDB43.
The largest HTPE43 has a C100 rating of 33,827 N per rail, and two parallel rails carry twice the load of one. Maximum recommended speed is 0.8 m/s, and the recommended temperature range is -20°C to 120°C. Raceways ship pre-lubricated, with additional lubrication recommended every 100 km.

Which guide fits your application?
- Compact guide with a choice of preload: Miniature Linear Guides.
- Torque and linear travel together: Torque Splines.
- Compact motorized slide with up to 24 inches of travel: 300 Series.
- Larger assembled stage up to 72 inches long: 200 Series.
- Long extension from a heavy-duty rail: Telescoping Rails.

Frequently asked questions
What is preload in a linear guide?
Preload is a controlled load between the runner block and rail that removes internal play, increasing stiffness and precision at the cost of friction and life.
Does more preload mean better accuracy?
More preload improves stiffness, precision, and torsion resistance, but it also increases friction and reduces life. Choose the class that fits your application.
What is the difference between PTS and PTA torque spline bushings?
The standard PTS bushing has 0.005 to 0.009 inch of rotational backlash. The PTA anti-backlash bushing is preloaded for zero backlash.
What is the difference between partial and full extension telescoping rails?
Partial extension rails (HTPE) travel part of their length. Full extension rails (HTDB) travel beyond their length.
How often should a miniature linear guide be lubricated?
Speed, load, stroke length, and operating environment all affect the interval, but it should not exceed one year.
